3ecommunications.net

Home > High Cpu > Cisco Fed Process

Cisco Fed Process

Contents

Switch # show controllers cpu-interface ASIC Rxbiterr Rxunder Fwdctfix Txbuflos Rxbufloc Rxbufdrain ------------------------------------------------------------------------- ASIC0 0 0 0 0 0 0 ASIC1 0 0 0 0 0 0 cpu-queue-frames retrieved dropped Register Hereor login if you are already a member E-mail User Name Password Forgot Password? Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions This Document Applies to These Products Catalyst 3750 Series Switches Catalyst 3750-E You must manually prune the ports with non-Cisco IP phones. this contact form

You can pull statistics from SNMP with very limited resources required from the stack.I have disabled the http but not secure http. 0 Jalapeno OP Tdawg1982 Aug 12, Common reason is we constantly move computers around (college environment). The sequence of actions in the examples: After the debug platform cpu-queue host-q command was entered, a single packet was received. Port security has been looked into, unfortunately management has decided not to use this for various reasons. http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/troubleshooting/cpu_util.html

Cisco Fed Process

The log Keyword in ACL The Catalyst 4500 supports logging of packets detail that hit any specific ACL entry, but excessive logging can cause high CPU utilization. The easiest way to slow down the mac-moves is with port-security. The CPU is doing both of these functions simultaneously.

The first function is run the different processes under IOS to carry out the function for a switch operating in a network. show ip route summary Shows the number of route entries used by each protocol. During a routine IOS update, going from 15.0.2 to 15.2-1 (most recent SE) we noticed a pretty significant CPU increase, from an average of about 30% to 60% and higher during How To Check Bandwidth Utilization On Cisco Router Any ports in disabled status that you haven't placed there administratively? 0 Jalapeno OP Tdawg1982 Aug 12, 2014 at 2:16 UTC Ok, I just took another one..

If the CPU is busy 5% of the time then the CPU is idle the other 95% of the time. Cisco Router High Cpu Interrupts Use the access list counters as a way to keep track of ACL hits. DHCP or IEEE 802.1x failures if the switch cannot forward or respond to requests. Use the information in Table 1 and the conclusion that you drew in Step 1.

See the examples in the “When High CPU Utilization Is a Problem” section. Ip Input High Cpu If you do not have the authority to change the /etc/crontab file, run the script in a separate process, like this: while [ 1 ]; do ./router-script ; sleep 300; done Sort by: OldestNewest Sorting replies... Figure 1 shows these queues.

Cisco Router High Cpu Interrupts

See the “CPU Receive Queues” section for details about the CPU queues. http://www.cisco.com/c/en/us/support/docs/switches/catalyst-3850-series-switches/117594-technote-hicpu3850-00.html Table 3 shows the number of TCAM resources available on each of the Catalyst 4500 Supervisor Engines and switches. Cisco Fed Process To support wake-up proxy, at least three computers must be awake for each subnet. Hulc Led Process High Cpu Will give mac-address-table notification a go, and see if we can find any patterns. "Since you're getting a large number of MAC flaps between switchports, it's hard to find where the

Because the switch hardware sees the CPU receive-queue dropped packets as sent to the supervisor, the dropped packets are called Supervisor TxQueue Drop Statistics in the command output. weblink The Meta-data is for internal use by the system, but the Data output provides actual packet information. This process is for internal path creation. Have this information ready when you contact Cisco technical support to reduce the time to resolve the problem. Show Memory Usage Cisco

Fast switching is enabled by default. Background Information Before you look at the CPU packet-handling architecture and troubleshoot high CPU utilization, you must understand the different ways in which hardware-based forwarding switches and Cisco IOS Software-based routers You use a different debug command to turn debugging on and off for each CPU receive queue. http://3ecommunications.net/high-cpu/show-memory-usage-cisco.html Search IT Knowledge Exchange Join / Login IT Knowledge Exchange a TechTarget Expert Community Questions & Answers Discussions Blogs Tags Welcome to TechTarget's expert community for technology professionals.

debug Commands Note: Refer to Important Information on Debug Commands before you use debug commands. Arp Input High Cpu Remove the ACL which caused the overflow or minimize the ACL to avoid overflow. After you identify the reason, the administrators can perform either of these actions: Corrective Action—This can include configuration or network changes, or the creation of a Cisco Technical Support service request

Configuration - Check the switch/interface/feature configuration CoPP/Hardware Rate Limiter - Ensure CoPP and HWRL are configured properly.

Similar to Cisco routers, switches use the show processes cpu command in order to show CPU utilization to identify the causes of high CPU utilization. Therefore, if you configure an excessive number of ACL entries, you exceed the TCAM capacity. One (or more) hosts having an "interface" route? How To Check Utilization On Cisco Router Interface This information is useful to identify any counts that are particularly high and incrementing rapidly.

Ports 1 through 24 belong to ASIC 0. They were taken within seconds of each other and the Cisco Network Assistant is showing different CPU usage vs CLI. 0 Sonora OP Jason3402 Aug 12, 2014 at Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions This Document Applies to These Products Catalyst 3850 Series Switches Share Information his comment is here Each CPU receive queue has a packet-count maximum.

This mechanism allows the CPU to run high-priority processes when necessary, and the idle CPU cycles that remain are used for the low-priority processes. However, due to the differences in architecture and forwarding mechanisms between Cisco routers and switches, the typical output of the show processes cpu command differs significantly. L2 protocol—Used for protocol packets such as UDLD, and so on. Switch# show processes cpu sorted 5sec CPU utilization for five seconds: 64%/19%; one minute: 65%; five minutes: 70% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 186 19472027 64796535 300

Only three packets are shown. The second section contains the actual commands that are sent to the router.