3ecommunications.net

Home > Error Code > Error Code 0142 Dell Optiplex 755

Error Code 0142 Dell Optiplex 755

Contents

If the automatic repair feature is unable to repair these errors, replace the drive. normal Summary progress and operational messages are displayed on the system console in addition to the messages displayed by the min setting. If the automatic repair feature is unable to repair these errors, replace the drive. true 3. his comment is here

Because ASR relies on firmware diagnostics to detect faulty devices, diag-switch? Sorry, there was a problem flagging this post. Minor (Alarm2) Amber Application state User sets Minor alarm onii. -- On Open Closed Minor fault detected. Home | Invite Peers | More UNIX Groups Your account is ready. http://www.unix.com/solaris/25519-rsc-selftest-failed-return-code-1-a.html

Error Code 0142 Dell Optiplex 755

Ten or more instances of information on data positioning and location could not be found. false false ansi-terminal? SUNW,[email protected] Tests the registers of the on-board FC-AL controller and FC-AL subsystem (Loop A).

The following is a sample of .show-post-results output. {2} ok .show-post-results CPU0/Memory: OK CPU1/Memory: OK CPU2/Memory: OK CPU3/Memory: OK CPU4/Memory: OK CPU5/Memory: OK CPU6/Memory: OK CPU7/Memory: OK Schizo0: OK Schizo1: OK A sample OpenBoot Diagnostics menu is shown below. There could be media errors present on this drive. To obtain additional information concerning the error condition, use niDMM_GetError.

This opens a log window from which you can choose to view the following logs: Information -- Detailed versions of all the status and error messages that appear in the test Dell Hard Drive Self Test Unsuccessful Status 79 Set the obdiag-trigger variable to power-on-reset, error-reset, or user-reset. So if 'chkdsk /f /r' is much differnet from 'chkdsk /r' or any hope, then I am ready, otherwise its meaningless to spoil one day. Off Offiii Closed Open Transient state.

[email protected],0 Performs a checksum of the flash PROM containing the OpenBoot firmware. Once reported, our moderators will be notified and the post will be reviewed. They are sent to ttya even when output-device is set to screen. true Note - The default setting for auto-boot-on-error?

Dell Hard Drive Self Test Unsuccessful Status 79

For more information, see How to Check Whether SunVTS Software Is Installed. 4. by Saroku / July 3, 2011 1:08 AM PDT In reply to: Rebuild array? *** DISCLAIMER *** The following information you must use at your own risk.. Error Code 0142 Dell Optiplex 755 Check your floppy and retest. Hard Drive Error Code 0142 Repair Tip You cannot run OpenBoot Diagnostics reliably after halting the operating system or aborting the operating system with the Stop-A keyboard command (or an equivalent abort key sequence).

Are you on V490 ? :)eNJOY Mohammed Tanvir Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving... this content You may need to rescan to ensure that the repairs were effective. Re-test Drive 138 Still Busy Timeout Timeout from checking busy bit. See OpenBoot Diagnostics Menu and Running OpenBoot Diagnostics. Dell Epsa Error Codes

You may need to rescan to ensure that the repairs were effective. diag-switch? = true ok To set or change the value of an OpenBoot configuration variable, use the setenv command. Replace the drive if the error repeats. weblink After pulling a few teeth, they are coming out this morning to replace the HD.

They may be remapped any time in the later use of the disk.    At this point, warranty replacement of the disk is not yet possible, only if the health drops further.    Poor|Excellent Yes No Document Quality? false--Default mode: Do not run POST or OpenBoot diagnostics tests.

This may be an anomaly.

The drive has not responded to the SMART test request. It may also be due to a defective connection. The following table lists the devices provided with a typical system and describes the self-test of each device. Designed for remote access.

This state represents the default mode of the relay contacts in the normally closed state. 2 (TableFootnote) NO state is the normally open state. Replace the drive if the error repeats. Note: Problems in systems with verbosity set to none might be deemed not diagnosable, rendering the system unserviceable by Sun. check over here Replace your cable and retest.

Retest the drive. Re-test Drive 148 Not Selected Drive not selected. This may be an anomaly or a defect with the drive. Preview post Submit post Cancel post You are reporting the following post: Error: Return code 7 hard drive failure This post has been flagged and will be reviewed by our staff.

Check the links below for the steps to run a test with DLG and for the replacement options that we have.  How to test a drive for problems using Data Lifeguard Replace the drive.